Genelec 8340A SAM™ Studiomonitori valkoinen
Genelec 8340A SAM™ Studio Monitor White
Elevate the accuracy of your audio monitoring to a new level with the precision and adaptability of the 8340A Smart Active Monitor.
The unvarnished truth
Top professionals the world over in recording studios, post-production houses, digital edit suites, radio, TV and outside broadcasting have come to rely on the unvarnished truth of the 8340A. Its wide and stable sweet spot promotes accurate, reliable mix decisions, and its bulletproof durability is essential for mission-critical applications.
Truly optimised monitoring
As a Smart Active Monitor, the 8340A integrates closely with our GLM software via which it can be configured and calibrated for your listening environment, compensating for detrimental room influences to create a truly optimised monitoring solution from mono to immersive. So if you need to work in challenging acoustic spaces, the 8340A is your powerful but clever monitoring companion.
1 x 8340A monitor
1 x mains cable 1,8 m
1 x RJ45 cable 5 m
1 x operating manual
Technical Specifications
System Specifications
Frequency Response
45 Hz - 20 kHz (± 1.5 dB)
Low cutoff -6dB
38 Hz
High cutoff -6dB
22 kHz
SPL
Peak SPL
≥118 dB
Maximum peak acoustic output per pair in a listening room with music material at 1 m.
Short term max SPL
≥110 dB
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
Long term max SPL
≥100 dB
Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver unit protection circuit) at 1 m.
Self-generated noise
Self-generated noise
≤5 dB
Self generated noise level in free field on axis (A-weighted).
Weight
Weight8.4 kg (18.5 lb)
Dimensions
Height
350 mm (13 25/32 in)
Height with Iso-Pod
365 mm (14 3/8 in)
Width
237 mm (9 11/32 in)
Depth
223 mm (8 25/32 in)
Enclosure
Enclosure material
Die cast aluminium
Enclosure type
Reflex port
Drivers
Driver type
Cone
Diameter
165 mm (6 1/2 in)
Driver type
Metal dome
Diameter
19 mm (3/4 in)
Directivity
Harmonic distortion
> 100 Hz ≤0.5 %
Group delay
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
3.0 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Amplifier Section
Amplifiers
150 W Class D
150 W Class D
Mains voltage
100-240 VAC 50/60Hz
Power consumption
ISS Active
≤1 W
Idle
≤12 W
Full output
180 W
Signal processing section
Connectors
Input
Analog signal input connector XLR female, balanced 10 kOhm.
Input
Digital signal input connector XLR female 110 Ohm.
Output
Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control
Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.
Validate your login